Installation Videos
 Polaris
RZR XP 1000/Turbo
Polaris RZR XP4 1000/Turbo
Polaris RZR S
Polaris General
 
 CanAm
Maverick X3
 
 
 
 
Yamaha
YXZ
 
 
 
 

 

 

 

 

 

 

 

My kit arrived with wrinkles or creases or random indentations making the product appear to be damaged or cut more than once.

Due to the shipping process, your kit may arrive with some wrinkles or creases. Don't worry, this is common and your kit is not damaged. A majority of the perceived damage is actually in the backing paper which makes it seem as if the vinyl is somewhat damaged. The vinyl itself is not damaged and will install without incident. Once the heat is used during the installation process, these wrinkles and creases will disappear since they are not in the vinyl itself, but the backing paper. If there are any actual cuts through the center of your graphic, please give us a call immediately and we will address the situation on a case by case basis.

In some instances, your kit will arrive with surface indentions from the perforated backing paper. This is also normal and more prevalent in colder temperatures and climates. After installation, (very carefully) use a heat gun, preferred over a hair dryer, in a general sweeping motion over the affected areas to raise the temperature of the vinyl to about 125F which should make the imperfections disappear. Please refer to the letter below from the Senior Technologist-Technical Service professional from 3M.

"Vinyl is a very soft material. When it is formed it takes on a “memory”. That memory remembers the surface gloss, size and shape of the original material. Because it is soft the material can get an impression when another item is pressed against it. Typically, the memory will start correcting that impression as soon as the offending pressure is removed. At room temperature, this process can take a couple of weeks. After installation, if you use a hair dryer or heat gun (very carefully) to raise the temperature to about 125F the re-glossing process will speed up greatly." -- Mark A. Elvester | 3M Senior Technologist - Technical Service

 

 

Graphics Wrap Kit - General Installation Instructions

Congratulations on your purchase of custom graphics! These instructions are general in nature and will provide the basics needed to properly install your graphics.

- Read and understand these instructions before installing product
- Ensure doors are securely latched prior to operating vehicle. Do not use product if there is any sign of damage

Disclaimer

We do not recommend covering or removing any factory warning labels. We will not be held responsible or liable in any way for any injuries or death, directly or indirectly resulting from covering or removal of factory warning label.   NOTE: If your graphic kit is designed to coincide with an OEM graphic scheme for an associated model, please understand that door graphic colors are selected and made to color match as close as possible. Due to vehicle use, plastics color and paint variations. The colors are not always a perfect in every case leading to slight variations.

General Notes:

- We have done our best to make the graphics kit as easy as possible to install but if possible, seek professional help.
- Install graphics kit in a 60°F - 100°F environment.
- Properly cleaning the graphic application surface before installation is critical (see Step 2 for reference).
- Take your time and plan on spending a few hours installing your graphics.
- IMPORTANT: There is no need to use soapy water to install our graphics.

Step 1: Thoroughly clean all parts of the surface area that the graphics will be applied to. Remove any factory installed graphics in the subject area as well. Use isopropyl alcohol for cleaning/prepping the surface that you are applying the graphics to. Properly cleaning the application surface is required for proper graphic adhesion.

Step 2: For the doors, remove door skins by unfastening hardware mounting them onto the door frames. Once the door skins are removed lay them on a flat surface such as the ground or a table/work bench.

Step 3: Once proper alignment is achieved, pick a corner to start with. Roll back the edge of the graphic on starting corner. Remove the paper backing and apply corner to the door skin surface. Make sure the unapplied graphic is still lined up after the starting corner is applied. After entire graphic is lined up, peel back more backing paper from the unapplied graphic and use your thumb or a small squeegee to flatten out the graphic to the door surface. If you have a high point on the graphic you are installing, start at the high point and work your way out/down toward the rest of the kit. {Note: Be firm with graphic application to ensure any air bubbles are removed.}

Step 4: You will continue the same application process in step 3 for the remaining graphics on the vehicle:

Place graphics on the area with paper backing still on graphics to get an idea of how they will lay and how to achieve proper alignment relative to shape of the skin.

Once proper alignment is achieved, pick a corner to start with. Roll back the edge of the graphic on starting comer. Remove the paper backing and apply corner to the door skin surface. Make sure the unapplied graphic is still lined up after the starting corner is applied. After entire graphic is lined up, peel back more backing paper from the unapplied graphic and use your thumb or a small squeegee to flatten out the graphic to the door surface. If you have a high point on the graphic you are installing, start at the high point and work your way out/down toward the rest of the kit. {Note: Be firm with graphic application to ensure any air bubbles are removed}.

Step 5: When you add heat from a blow dryer or heat gun, the kit can stretch up to one inch in any direction so be careful using heat while pulling or holding the graphics. If you end up with some small wrinkles at the very last edge of a graphic area, apply a little heat and tap it down with your finger to flatten these areas out.

Step 6: Repeat process for remaining surfaces until all graphics in kit are applied accordingly.

Step 7: After installation is complete on all areas, let the graphics kit sit for 24hrs. With a razor blade, knife or scissors; carefully cut an "X" or single slit from the top side of the graphics, through all hardware holes in the door skin to allow for hardware to pass back through. Re-install all door skins back on to door frames and check   to make sure doors are functioning properly before use.

Please call us at 480.888.0202 with any questions.

 

Installation Videos

 

Wolf Designs - Rocker Install Video



Wolf Designs - RZR Turbo Hood Install Video

Wolf Designs - TMW Door Install Video



Wolf Designs - Fender Install Video

 

Wolf Designs - Roof Install Video

 

Wolf Designs Install Instruction Video


Wolf Designs Door Install Instruction Video